EZH 类似一个独立的内核，但是需要使用汇编来实现代码的录入。
知识点1
EZH需要一段RAM来运行自己的程序，所以在分散加载文件中需要把这部分RAM独立出来
以“EZH_SECT”命名， 如下
ezh_wt588.c
define EZH_CODE attribute((section("EZH_SECT")))
分散加载文件格式，这里我们用SRAMX作为EZH代码的执行区域
image.png
知识点2
所有的代码是宏，通过IDE生成2进制的可执行文件。并不能用C来开发。
知识点3
对应的IO口需要配置为EZH模式，在LPC5410x上只有P0组的IO口可以被配置为EZH的接口
IOCON->PIO[0][WT588_DATA] = PINFUNC_EZH | 1<<7 | 1<<8;
核心API
void wt588_cmdset(uint32_t command)
command这里就是发送的index号
细节1
EZH GPIO配置，这里用的是PIO0_9,
#define WT588_DATA 9
细节2
WD588 初始化部分，注意这里的65000 需要根据内核的主频来做修改，我这里用的应该是96MHz的
E_BCLR_IMM(GPO, GPO, WT588_DATA) // Set DATA IO to low for 5mS, start transfer
E_HEART_RYTHM_IMM(65000) // set the timer initial value
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(65000) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(65000) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(65000) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(65000) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(65000) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(65000) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(65000) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT
细节3
// Transfer bit-8
E_LSR(R0, R4, 8)
E_AND_IMMS(R1, R0, 0x01)
E_COND_GOTOL(AZ, set1) // If above Zero
E_COND_GOTOL(ZE, set0) // If Zero or Below
这段代码开始 就是按照每一个bit上是0还是1，
如果是0 则去set0 处，如果是1 则去set1 处
set0
E_BSET_IMM(GPO, GPO, WT588_DATA) // Set DATAIO to high
E_HEART_RYTHM_IMM(2406) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(2406) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(2406) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(2406) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(2406) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(2406) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(2406) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(2406) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT
E_BCLR_IMM(GPO, GPO, WT588_DATA) // Set DATAIO to low
E_HEART_RYTHM_IMM(7225) // set the timer initial value: 600uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(7225) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(7225) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(7225) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(7225) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(7225) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(7225) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(7225) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT
E_GOTO_REG(RA)
set1
E_BSET_IMM(GPO, GPO, WT588_DATA) // Set DATAIO to high
E_HEART_RYTHM_IMM(7225) // set the timer initial value: 600uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(7225) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(7225) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(7225) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(7225) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(7225) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(7225) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(7225) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT
E_BCLR_IMM(GPO, GPO, WT588_DATA) // Set DATAIO to low
E_HEART_RYTHM_IMM(2406) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(2406) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(2406) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(2406) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(2406) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(2406) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(2406) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT // wait for the timer decreate to 0
E_HEART_RYTHM_IMM(2406) // set the timer initial value: 200uS
E_WAIT_FOR_BEAT
