DS200XDSAG1A DS200VPBLG1A DS200UPSAG1AEC DS200UPSAG1ADB DS200UPSAG1A通用电气卡件DS200UPLAG1BDA DS200UPLAG1B DS200UPLAG1ADC DS200UPLAG1ABA DS200UDSAG1ADE DS200UDSAG1A DS200UCVAG1ABB DS200UCPBG7 DS200UCPBG6A DS200UCPBG6
安装和调试基于RISC的MVME187单板计算机；基于VMEbus的中低端OEM的高性能引擎以及集成系统、嵌入式控制器和其他单板计算机应用程序。本手册提供：❏ 第2章中的一般板级硬件描述❏ 第3章中的硬件准备和安装说明❏ 第4章中的调试器一般信息❏ 调试器/监视器命令，以及有关使用第5章中的187Bug调试器❏ 启动和故障排除所需的其他信息MVME187 RISC单板计算机，
包括–附录A中的配置和环境命令–附录B中控制器的磁盘/磁带控制器数据187Bug支持的模块–附录C中的网络控制器数据–附录D中的CPU板故障排除程序-附录术语、惯例和定义中的EIA-232-D互连本手册中使用数据和地址参数数字格式在本手册中，识别数字的字符格式位于数据和地址参数之前，如下所示：例如，“12”是十进制数12，“$12”是十进制数字十八除非另有规定，否则所有地址引用均十六进制。信号名称约定对于电平为或的信号，信号名称后面有一个星号（*）边缘显著性：指定十六进制字%百分比指定二进制&符号指定十进制术语*表示数量信号低时，信号为真或有效。重要的该信号启动的动作发生在高电平到低转换。 installation, and debugging of theRISC-based MVME187 Single Board Computer; a highperformance engine for VMEbus-based low- and mid-range OEM
and integrated systems, embedded controllers, and other singleboard computer applications.
This manual provides:
❏ A general Board Level Hardware Description in Chapter 2
❏ Hardware Preparation and Installation instructions in Chapter 3
❏ Debugger General Information in Chapter 4
❏ Debugger/monitor commands, and other information about
Using the 187Bug Debugger in Chapter 5
❏ Other information needed for start-up and troubleshooting of
the MVME187 RISC Single Board Computer, including
– Configure and Environment Commands in Appendix A
– Disk/Tape Controller Data in Appendix B for controller
modules supported by 187Bug
– Network Controller Data in Appendix C
– Procedures for Troubleshooting CPU Boards in Appendix D
– EIA-232-D Interconnections in Appendix Terminology, Conventions, and Definitions
Used in this Manual
Data and Address Parameter Numeric Formats
Throughout this manual, a character identifying the numeric
format precedes data and address parameters as follows:
For example, “12” is the decimal number twelve, and “$12” is the
decimal number eighteen.
Unless otherwise specified, all address references are in
hexadecimal.
Signal Name Conventions
An asterisk (*) follows signal names for signals which are level or
edge significant:
$ dollar specifies a hexadecimal character
% percent specifies a binary number
& ampersand specifies a decimal number
Term * Indicates
level
significant The signal is true or valid when the signal is low.
edge
significant
The actions initiated by that signal occur on high
to low transition.
