||
| ------------- |:-------------:| -----:|
|379 | Exasmoc is loading new CON File（Exasmoc正在加载新的CON文件）。| 在线整定完成，并读取新的CON文件。 MV和DV的历史值不会丢失。|
|388 |Bad Main Controller name（主控制器名称为坏）。| 由于主控制器名称无效，控制器无法启动。联系产品支持。|
|389| Bad Sub Controller name（子控制器名称为坏）。 |由于子控制器名称无效，子控制器无法启动。联系产品支持。|
|391| Exasmoc controller was terminated %s（ Exasmoc控制器已终止％s）。 |控制器停止。|
|392 |Desired Status of the Tag(%s) value is OFF（期望的位号状态（％s）值为OFF）。 |主控制器的期望状态为0（OFF）。确认分配给期望状态的位号值和质量代码。|
|393| Invalid Economic Function is Selected （选择了无效的经济函数）。| 未选择有效的经济函数。|
|394| Bad DEF File Format（错误的DEF文件格式）。 |DEF文件格式与在线控制器不匹配。使用PCTP重新配置定义文件。|
|395| Total length of MC and SC name must be under 24（MC和SC名称的总长度必须小于24）。| MC和SC名称的总长度应等于或小于24个字符。通过PCTP重新配置控制器。|
|396 |The length of Main Controller name must be under 10（主控制器名称的长度必须小于10）。| MC名称的总长度应小于等于10个字符。通过PCTP重新配置控制器。|
|397| MV/CV Plotting Points are too many（MV / CV绘图点太多）。| MV或CV绘图点的数量超过最大值。减少绘图点。|
|399| Message Queue is Full（消息队列已满）。 |一次生成太多的消息。确认某些消息未存储在历史消息中。|
|1001 | Tag name (%s) is invalid（位号名称（％s）无效）。 | 定义的位号名称不正确。它在FCS中未定义或无法访问。在DCS中确认相关位号名称。|
|1002| OPC Read() Error (%s) （OPC Read（）错误（％s））。 | 发生OPC读取错误。在DCS中确认相关位号名称。|
|1003| [%s] Tagname (%s) is invalid（[％s]位号名（％s）无效）。| T定义的位号名称不正确。它在FCS中未定义或无法访问。在DCS中确认相关位号名称。|
|1004| [%s] OPC Read() Error (%s) （ [％s] OPC Read（）错误（％s））。| 发生OPC读取错误。在DCS中确认相关位号名称。|
|1005| OPC Write() Error (%s) （OPC Write（）错误（％s））。| OPC写入错误。在DCS中确认相关位号名称。|
|1006| [%s] OPC Write() Error (%s)（[％s] OPC Write（）错误（％s）。）| OPC写入错误。在DCS中确认相关位号名称。|
|1007| [%s] Invalid CV Set Range（ [％s] CV设置范围无效）。| CV设置范围高限或设置范围低限不正确。检查SRH和SRL值。|

原文：

||
| ------------- |:-------------:| -----:|
|379 |Exasmoc is loading new CON File |The online tuning was done and a new CON file is read. The history of MV and DV remain without missing.|
|388| Bad Main Controller name |The controller cannot start due to the invalid main controller name. Contact to the product support.|
|389| Bad Sub Controller name |The sub-controller cannot start due to the invalid sub-controller name. Contact to the product support.|
|391 |Exasmoc controller was terminated %s |The controller stopped.|
|392| Desired Status of the Tag(%s) value is OFF| Desired Status of the main controller is 0 (OFF). Confirm the tag value and quality code assigned to Desired Status.|
|393 |Invalid Economic Function is Selected |Effective Economic Function is not selected.|
|394 |Bad DEF File Format| DEF file format does not match with the online controller. Re-configure the definition file using PCTP.|
|395 |Total length of MC and SC name must be under 24 |Total length of MC and SC name should be equal to or less than 24 characters. Re-configure the controller by PCTP.|
|396| The length of Main Controller name must be under 10 |Total length of MC name should be equal to or less than 10 characters. Re-configure the controller by PCTP.|
|397| MV/CV Plotting Points are too many |The number of MV or CV plotting point is over maximum. Reduce the Plotting point.|
|399 |Message Queue is Full |The too many messages are generated at once. Confirm some messages are not store in the historical message.|
|1001 | Tag name (%s) is invalid Defined tag name is not correct.| It is not defined in the FCS or cannot be accessed. Confirm the related tag name in DCS.|
|1002| OPC Read() Error (%s) |OPC Read error occurred. Confirm the related tag name in DCS.|
|1003| [%s] Tagname (%s) is invalid T defined tag name is not correct. |It is not defined in the FCS or cannot be accessed. Confirm the related tag name in DCS.|
|1004| [%s] OPC Read() Error (%s) | OPC Read error occurred. Confirm the related tag name in DCS.|
|1005| OPC Write() Error (%s) | OPC Write error occurred. Confirm the related tag name in DCS.|
|1006 | [%s] OPC Write() Error (%s)| OPC Write error occurred. Confirm the related tag name in DCS.|
|1007| [%s] Invalid CV Set Range| CV Set Range High or Set Range Low is not correct. Conform the value of SRH and SRL.|

2017.1.27